pre ran wiring and panel
Results 1 to 5 of 5
Like Tree1Likes
  • 1 Post By Sapper12

Thread: pre ran wiring and panel

  1. #1
    Junior Member
    Join Date
    Apr 2019
    Posts
    23
    Member #
    30995
    Liked
    5 times

    pre ran wiring and panel

    Looking for suggestions before I cut and regret.

    took off the panel that screws on and it is solid behind the panel, is it ok to cut out the whole panel or will it make something too weak? Cutting out the whole panel seems like the easiest way to get to the pre wired plugs behind the dash

    I haven't been able to really get close to the pre wired plugs behind the dash to see how to use them, they are fairly big plugs are they set up to just hook single wires to or is there a plug i need to buy kinda like a car radio plug to wire in a stereo?

  2. #2
    Senior Member
    Join Date
    Apr 2015
    Location
    Southwest Houston
    Posts
    544
    Member #
    4972
    Liked
    261 times
    I used a 5-6" diameter hole saw so there's plenty of room for wiring. No issues here.
    2018 Wildcat XX green/black

    32" ITP Cryptids
    Warn VRX 45-S winch
    HMF Titan QS Blackout exhaust
    Custom roof
    Speedwerx steering bushing
    Custom winch mount
    Speedwerx alternator delete kit
    Custom tow ring
    Suspension lifted 4"
    Venom secondary spring
    Assault Industries tie rods

  3. #3
    Junior Member
    Join Date
    Apr 2019
    Posts
    23
    Member #
    30995
    Liked
    5 times
    I finally got time to really mess with it and just got the pre ran plugs pushed through the toggle switch panels. Its pretty cool how plug and play they are i wish they would have wired up the jumpers though for toggle switches with lights on them.

  4. Remove Advertisements
    WildcatForums.net
    Advertisements
     

  5. #4
    Junior Member
    Join Date
    Jul 2018
    Posts
    8
    Member #
    29693
    Liked
    4 times
    I cut out most of my panel to fit radio, stereo and intercom. Still seems to be plenty strong

  6. #5
    Junior Member
    Join Date
    Jun 2019
    Posts
    16
    Member #
    31299
    Liked
    6 times
    Remove the the top fender on passenger side pretty simple and then you get decent access to the pre wired plugs!
    Just FYI you can pop the 3 female connectors out of the plastic plug 1 is 12v switched, 1 ground, 1 is 12v power to your accessory with small eye glass screwdriver and make pigtails 1 end male spade and other end female spade for your switch to just plug into the females you removed from factory plug. Use a 12v test light to know what is what then they are all the same! Then heat shrink and or wire loom to finish it! I did that to 3 of the pre wired plugs! Works excellent and now easy to work on as well for future!
    Last edited by Sapper12; 09-05-2019 at 09:52 PM.
    18wildcatxx likes this.


 

Sponsored Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBulletin® Version 4.2.3
Copyright © 2019 vBulletin Solutions, Inc. All rights reserved.
SEO by vBSEO ©2011, Crawlability, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
All times are GMT -6. The time now is 12:50 PM.