Alba stage 3 kit, first ride!
Results 1 to 9 of 9
Like Tree5Likes
  • 2 Post By Renojohn
  • 2 Post By Renojohn
  • 1 Post By Mocat

Thread: Alba stage 3 kit, first ride!

  1. #1
    Junior Member
    Join Date
    Feb 2019
    Posts
    15
    Member #
    30645
    Liked
    4 times

    Alba stage 3 kit, first ride!

    Finished installing my stage 3 kit from alba and took the xx out to the sand to try it out and dial it in. Install took approx 5 hours and I did need a little tech help from alba. They were great to work with and patient with all my questions.
    Low end power and responsiveness is definitely improved still working on clutching. Currently I’m sitting at approx 4500 feet in elevation and running 32” cst paddles.
    Clutch weights recommended are as follows from heal to toe 1,1,4 washers. I believe I need to reduce weight off the toe and add some to the heal and middle so I don’t flatten out so hard I’m only pulling 8700 rpm wot
    Attached Images Attached Images    
    raynmary and izom like this.

  2. #2
    Senior Member
    Join Date
    Apr 2012
    Location
    Kansas
    Posts
    2,813
    Member #
    1238
    Liked
    991 times
    Thanks for sharing! I almost bought the same kit but ended up going with the Speedwerx 3r kit and will be testing in the sand tomorrow. Right now on pavement with stock tires it is right at 9300 so figure the sand will pull rpm’s down a little.


    Sent from my iPhone using Tapatalk
    2014 X Limited
    April 2016 WOTM

  3. #3
    Junior Member
    Join Date
    Feb 2019
    Posts
    15
    Member #
    30645
    Liked
    4 times
    Yea no worries if anybody has any clutch set up recommendations it be greatly appreciated. I was going to try 1,2,3 see what that does

  4. Remove Advertisements
    WildcatForums.net
    Advertisements
     

  5. #4
    Supporting Vendor
    Supporting Member

    Join Date
    Mar 2012
    Posts
    182
    Member #
    1132
    Liked
    114 times
    With that amount of tire and elevation I would probably just try running the arms near empty. Take the weight off of the heel and middle for sure. Maybe try 2 washers only on the tip, and if that is still not enough then go bare weight.

    Nate
    Alba Racing

  6. #5
    Junior Member
    Join Date
    Feb 2019
    Posts
    15
    Member #
    30645
    Liked
    4 times
    Nate thank you, removed the weight from the gel and middle placed two washers on the tip and made a world of difference
    thunder45 and izom like this.

  7. #6
    Senior Member
    Join Date
    Oct 2015
    Location
    Chesterfield Michigan
    Posts
    1,929
    Member #
    5650
    Liked
    1570 times
    Thanks for the update, I've been looking at the Alba stage 3 also, it's going to be a spring update for me.
    Ray
    2019 Wildcat XX
    Aluminum roof, Front windshield, rear window
    Sound system
    30" Motovators

  8. #7
    Junior Member
    Join Date
    Feb 2017
    Posts
    19
    Member #
    19769
    Liked
    12 times
    Just did stage 3 alba kit. Awesome! Usually about 1500 to 2000 ft. Still need a little fine tunning on the cam arms not quite getting engagement and max rpm where it needs to be. Took it to the sand last week did great. Dead even out of the hole vs XP turbo lost in mid range then almost got back in top end (2 car legnths) quarter drag on damp sand. Ran three times same result. Should be nuts when I get dialed in. BIG IMPROVEMENT
    izom likes this.

  9. #8
    Senior Member
    Join Date
    Nov 2015
    Location
    landofarnolds.
    Posts
    1,171
    Member #
    5717
    Liked
    672 times
    ...vids !?? ;- ()
    wildcat 1000 limited 2013,5

    H1 650 TRV 2009

  10. #9
    Junior Member
    Join Date
    Feb 2017
    Posts
    19
    Member #
    19769
    Liked
    12 times
    I was busy driving. Dont have a go pro let me check with a couple friends they may have video. I will post it they have it.


 

Sponsored Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBulletin® Version 4.2.3
Copyright © 2020 vBulletin Solutions, Inc. All rights reserved.
SEO by vBSEO ©2011, Crawlability, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
All times are GMT -6. The time now is 11:14 AM.